Skip to content

Cutters and bits

4mm Tungsten Carbide Flat-Tip Tapered Engraving Bit, DLC Diamond-Like Coating, for Metal

$3.45¥23.00 observed on the listing, 27 October 2026. Not a quote.

We confirm the exact configuration, voltage and what is included with the seller before ordering. Single units and trial orders are fine.

What this DLC coated engraving bit listing says

DLC means diamond-like carbon, a thin hard coating applied to cutters, and this listing offers a 4mm tungsten carbide flat-tip tapered engraving bit with that coating for metal lettering. DLC is mainly marketed for non-ferrous metals such as aluminum, and for reducing built-up edge, so the target material matters. The coating type is only the seller's claim, with no thickness or hardness value. The title omits cone angle, tip width, overall length and whether 4mm is the shank or the body. The observed price is US$3.45 (CNY 23.00).

TypeFlat-tip tapered engraving bit
MaterialTungsten carbide
CoatingDLC (seller claim)
Size4mm (shank or body not specified)
UseMetal lettering

What we confirm with the machine seller first

  • What cone angle and tip width apply to the observed price, and which other angle and tip combinations are in the variant list?
  • Is the DLC coating a documented process, such as PVD with a stated thickness, and which metals is it intended for?
  • Does 4mm describe the shank diameter, and what overall length and cutting length does the bit have?
  • How does this coated bit last compared with an uncoated or titanium-coated one, and have you run it on stainless steel?

Who this machine or part suits

Aimed at an engraver of metal nameplates who wants to trial a coated bit for longer life on aluminum or other non-ferrous metals, accepting the coating claim until tested. It is the wrong choice for wood or acrylic work, where a coating adds cost without much benefit.

Goods cost at the listed price

Goods only, at the observed unit price for the configuration listed. Sellers may change price by spindle, controller or table size, so the figures are arithmetic, not a quote.

QuantityGoods at $3.45 eachIn yuan
20$69.00¥460
100$345¥2,300
300$1,035¥6,900

Crating, seller delivery to the warehouse, our fee, international freight and import duty are added; for a machine, crating and freight can be a large part of the delivered cost.

How this price compares with other cutters and bits listings

Of 14 cutters and bits listings, this is the 12th cheapest at $3.45; the range is $0.92 to $7.81, median $2.56. Price gaps between machine listings usually reflect frame, spindle, drive or controller differences, so compare the same configuration.

Two checks that matter for CNC router bits orders

Confirm shank diameter against your collet

A bit only works if its shank matches the collet bore. These listings mention 3.175 mm, which is 1/8 inch, and 4 mm. Those figures are normally shank diameters, but ask the seller to confirm, because the two sizes cannot share one collet. Write the shank size into the order, and ask whether a listing offers several sizes under a single price.

Clarify length and the '70 degree' label

Overall length, cutting length and neck clearance decide how deep a bit can cut before the shank touches the work. The long flat end mill carries a 70 degree label that is unclear on its own, so ask whether it describes hardness, a helix or an angle. Request cutting length and total length for each variant.

All cutters and bits checks and listings

Questions about this CNC listing

Do I need to inspect CNC router bits when they arrive?

Yes, a quick check is sensible, because small tips can chip in transit and a seller can ship a different variant. We receive the goods at our warehouse in China and can check tip condition, markings and counts against your order before shipping. Tell us in advance which dimensions to measure, such as shank diameter and angle.

Is this the price of the complete machine?

No. It is what the listing showed on 27 October 2026, converted at ¥6.668 to the dollar, and listings often price a base configuration. Spindle, controller, accessories, crating, our fee, freight and import duty are confirmed and quoted separately.

Can I order just one unit of the DLC coated engraving bit?

For machines, usually yes: many sellers ship single units. For tooling and spare parts the seller may set a minimum per variant, which we confirm before ordering.

Buying the DLC coated engraving bit for your workshop or a customer? Send the quantity, your voltage and the destination and we return an itemised delivered price.

Price this landed

Wholesale desktop CNC machines from China covers how small orders work. Delivering the machine to United States or United Kingdom? See the guides for wholesale desktop CNC machines for United States and wholesale desktop CNC machines for United Kingdom. Figures and images are from the seller's Taobao listing as recorded on 27 October 2026. A machine listing can change configuration, price or availability at any time, and specifications on it are the seller's claims until we confirm them.